A.1 Messages de l'amorce d'un Linux
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 2.6.25-2-686 (Debian 2.6.25-6) (maks@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Fri Jun 27 03:23:20 UTC 2008
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001fe71000 (usable)
[ 0.000000] BIOS-e820: 000000001fe71000 - 000000001fe73000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001fe73000 - 000000001fe94000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001fe94000 - 000000001ff00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 510MB LOWMEM available.
[ 0.000000] Scan SMP from c0000000 for 1024 bytes.
[ 0.000000] Scan SMP from c009fc00 for 1024 bytes.
[ 0.000000] Scan SMP from c00f0000 for 65536 bytes.
[ 0.000000] found SMP MP-table at [c00fe710] 000fe710
[ 0.000000] Entering add_active_range(0, 0, 130673) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 130673
[ 0.000000] HighMem 130673 -> 130673
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 130673
[ 0.000000] On node 0 totalpages: 130673
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 988 pages used for memmap
[ 0.000000] Normal zone: 125589 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000FEBA0, 0014 (r0 DELL )
[ 0.000000] ACPI: RSDT 000FD506, 0038 (r1 DELL GX60 6 ASL 61)
[ 0.000000] ACPI: FACP 000FD53E, 0074 (r1 DELL GX60 6 ASL 61)
[ 0.000000] ACPI: DSDT FFFD50FE, 2556 (r1 DELL dt_ex 1000 MSFT 100000D)
[ 0.000000] ACPI: FACS 1FE71000, 0040
[ 0.000000] ACPI: SSDT FFFD7654, 00A7 (r1 DELL st_ex 1000 MSFT 100000D)
[ 0.000000] ACPI: APIC 000FD5B2, 005C (r1 DELL GX60 6 ASL 61)
[ 0.000000] ACPI: BOOT 000FD60E, 0028 (r1 DELL GX60 6 ASL 61)
[ 0.000000] ACPI: ASF! 000FD636, 0067 (r16 DELL GX60 6 ASL 61)
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:2 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 1ff00000:ded00000)
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129653
[ 0.000000] Kernel command line: root=/dev/hda1 ro quiet
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 2000.145 MHz processor.
[ 0.001515] Console: colour VGA+ 80x25
[ 0.001522] console [tty0] enabled
[ 0.001957] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.002656] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.004000] Memory: 508232k/522692k available (1753k kernel code, 13876k reserved, 728k data, 252k init, 0k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xdfe71000 ( 510 MB)
[ 0.004000] .init : 0xc0375000 - 0xc03b4000 ( 252 kB)
[ 0.004000] .data : 0xc02b6432 - 0xc036c640 ( 728 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02b6432 (1753 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084009] Calibrating delay using timer specific routine.. 4004.95 BogoMIPS (lpj=8009902)
[ 0.084076] Security Framework initialized
[ 0.084085] SELinux: Disabled at boot.
[ 0.084089] Capability LSM initialized
[ 0.084115] Mount-cache hash table entries: 512
[ 0.084367] Initializing cgroup subsys ns
[ 0.084375] Initializing cgroup subsys cpuacct
[ 0.084417] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 0.084423] CPU: L2 cache: 128K
[ 0.084426] CPU: Hyper-Threading is disabled
[ 0.084431] Intel machine check architecture supported.
[ 0.084439] Intel machine check reporting enabled on CPU#0.
[ 0.084442] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
[ 0.084448] CPU0: Thermal monitoring enabled
[ 0.084457] Compat vDSO mapped to ffffe000.
[ 0.084469] Checking 'hlt' instruction... OK.
[ 0.100417] SMP alternatives: switching to UP code
[ 0.103143] Freeing SMP alternatives: 16k freed
[ 0.103152] ACPI: Core revision 20070126
[ 0.141613] CPU0: Intel(R) Celeron(R) CPU 2.00GHz stepping 07
[ 0.141671] Total of 1 processors activated (4004.95 BogoMIPS).
[ 0.141813] ENABLING IO-APIC IRQs
[ 0.142001] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.184011] Brought up 1 CPUs
[ 0.184011] CPU0 attaching sched-domain:
[ 0.184011] domain 0: span 01
[ 0.184011] groups: 01
[ 0.184011] net_namespace: 548 bytes
[ 0.184011] Booting paravirtualized kernel on bare hardware
[ 0.184011] NET: Registered protocol family 16
[ 0.184011] ACPI: bus type pci registered
[ 0.208698] PCI: PCI BIOS revision 2.10 entry at 0xfbdfd, last bus=1
[ 0.208703] PCI: Using configuration type 1
[ 0.208732] Setting up standard PCI resources
[ 0.211911] ACPI: EC: Look up EC in DSDT
[ 0.240954] ACPI: Interpreter enabled
[ 0.240963] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.240993] ACPI: Using IOAPIC for interrupt routing
[ 0.278828] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.279433] * The chipset may have PM-Timer Bug. Due to workarounds for a bug,
[ 0.279436] * this clock source is slow. If you are sure your timer does not have
[ 0.279438] * this bug, please use "acpi_pm_good" to disable the workaround
[ 0.279492] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
[ 0.279497] pci 0000:00:1f.0: quirk: region 0880-08bf claimed by ICH4 GPIO
[ 0.279784] PCI: Transparent bridge - 0000:00:1e.0
[ 0.279823] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.280509] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 0.384911] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11 12 15)
[ 0.385294] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 15)
[ 0.385666] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 15)
[ 0.386039] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 15)
[ 0.386410] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[ 0.386783] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[ 0.387155] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[ 0.387533] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 9 10 11 12 15)
[ 0.388004] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.388148] pnp: PnP ACPI init
[ 0.388169] ACPI: bus type pnp registered
[ 0.415502] pnp: PnP ACPI: found 12 devices
[ 0.415508] ACPI: ACPI bus type pnp unregistered
[ 0.415515] PnPBIOS: Disabled by ACPI PNP
[ 0.416462] PCI: Using ACPI for IRQ routing
[ 0.416469] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.421770] ACPI: RTC can wake from S4
[ 0.421840] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.421847] system 00:00: iomem range 0x100000-0xffffff could not be reserved
[ 0.421851] system 00:00: iomem range 0x1000000-0x1fe70fff could not be reserved
[ 0.421855] system 00:00: iomem range 0xf0000-0xfffff could not be reserved
[ 0.421859] system 00:00: iomem range 0xfec00000-0xfec0ffff could not be reserved
[ 0.421863] system 00:00: iomem range 0xfee00000-0xfee0ffff could not be reserved
[ 0.421868] system 00:00: iomem range 0xffb00000-0xffbfffff could not be reserved
[ 0.421872] system 00:00: iomem range 0xffc00000-0xffffffff could not be reserved
[ 0.421893] system 00:0b: ioport range 0x800-0x85f has been reserved
[ 0.421897] system 00:0b: ioport range 0xc00-0xc7f has been reserved
[ 0.421902] system 00:0b: ioport range 0x860-0x8ff could not be reserved
[ 0.453472] PCI: Bridge: 0000:00:1e.0
[ 0.453477] IO window: e000-efff
[ 0.453484] MEM window: 0xff800000-0xff9fffff
[ 0.453489] PREFETCH window: disabled.
[ 0.453506] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.453553] NET: Registered protocol family 2
[ 0.453764] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.454115] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.454248] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.454482] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.454488] TCP reno registered
[ 0.454920] checking if image is initramfs... it is
[ 0.956087] Switched to high resolution mode on CPU 0
[ 1.232530] Freeing initrd memory: 6204k freed
[ 1.232896] Simple Boot Flag value 0x87 read from CMOS RAM was invalid
[ 1.232901] Simple Boot Flag at 0x7a set to 0x1
[ 1.234432] audit: initializing netlink socket (disabled)
[ 1.234456] type=2000 audit(1224762971.232:1): initialized
[ 1.234671] Total HugeTLB memory allocated, 0
[ 1.234858] VFS: Disk quotas dquot_6.5.1
[ 1.234905] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.235095] io scheduler noop registered
[ 1.235100] io scheduler anticipatory registered
[ 1.235102] io scheduler deadline registered
[ 1.235127] io scheduler cfq registered (default)
[ 1.235147] pci 0000:00:02.0: Boot video device
[ 1.235229] pci 0000:01:0c.0: Firmware left e100 interrupts enabled; disabling
[ 1.236353] isapnp: Scanning for PnP cards...
[ 1.590768] isapnp: No Plug & Play device found
[ 1.601170] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.601419] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.602660] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.605548] brd: module loaded
[ 1.605843] PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 1.608558] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.608570] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.609082] mice: PS/2 mouse device common for all mice
[ 1.609306] cpuidle: using governor ladder
[ 1.609311] cpuidle: using governor menu
[ 1.609944] TCP cubic registered
[ 1.609974] NET: Registered protocol family 1
[ 1.609995] NET: Registered protocol family 17
[ 1.610006] Using IPI No-Shortcut mode
[ 1.610494] registered taskstats version 1
[ 1.611036] Freeing unused kernel memory: 252k freed
[ 1.644803] input: AT Translated Set 2 keyboard as /class/input/input0
[ 2.024002] ACPI: ACPI0007:00 is registered as cooling_device0
[ 2.730904] usbcore: registered new interface driver usbfs
[ 2.730951] usbcore: registered new interface driver hub
[ 2.748277] usbcore: registered new device driver usb
[ 2.770230] USB Universal Host Controller Interface driver v3.0
[ 2.770305] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 2.770323] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 2.770328] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.770549] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 2.770594] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ff80
[ 2.770835] usb usb1: configuration #1 chosen from 1 choice
[ 2.770890] hub 1-0:1.0: USB hub found
[ 2.770910] hub 1-0:1.0: 2 ports detected
[ 2.872364] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.872371] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.872375] usb usb1: Product: UHCI Host Controller
[ 2.872378] usb usb1: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[ 2.872381] usb usb1: SerialNumber: 0000:00:1d.0
[ 2.872433] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 2.872450] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 2.872456] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.872533] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 2.872572] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ff60
[ 2.872771] usb usb2: configuration #1 chosen from 1 choice
[ 2.872820] hub 2-0:1.0: USB hub found
[ 2.872841] hub 2-0:1.0: 2 ports detected
[ 2.976369] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.976376] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.976381] usb usb2: Product: UHCI Host Controller
[ 2.976383] usb usb2: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[ 2.976386] usb usb2: SerialNumber: 0000:00:1d.1
[ 2.976438] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 2.976458] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 2.976464] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.976532] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 2.976573] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40
[ 2.976767] usb usb3: configuration #1 chosen from 1 choice
[ 2.976816] hub 3-0:1.0: USB hub found
[ 2.976835] hub 3-0:1.0: 2 ports detected
[ 3.010922] No dock devices found.
[ 3.062367] SCSI subsystem initialized
[ 3.080396] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.080402] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.080407] usb usb3: Product: UHCI Host Controller
[ 3.080410] usb usb3: Manufacturer: Linux 2.6.25-2-686 uhci_hcd
[ 3.080412] usb usb3: SerialNumber: 0000:00:1d.2
[ 3.080538] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
[ 3.080562] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 3.080568] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.080626] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
[ 3.084560] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.084569] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
[ 3.084591] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffa00800
[ 3.088709] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[ 3.088714] e100: Copyright(c) 1999-2006 Intel Corporation
[ 3.104594] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.104779] usb usb4: configuration #1 chosen from 1 choice
[ 3.104836] hub 4-0:1.0: USB hub found
[ 3.104856] hub 4-0:1.0: 6 ports detected
[ 3.149892] libata version 3.00 loaded.
[ 3.208406] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.208413] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.208418] usb usb4: Product: EHCI Host Controller
[ 3.208420] usb usb4: Manufacturer: Linux 2.6.25-2-686 ehci_hcd
[ 3.208423] usb usb4: SerialNumber: 0000:00:1d.7
[ 3.209087] ACPI: PCI Interrupt 0000:01:0c.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 3.299573] e100: eth0: e100_probe: addr 0xff8ff000, irq 18, MAC addr 00:08:74:ca:f4:bf
[ 3.325375] Uniform Multi-Platform E-IDE driver
[ 3.325383] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 3.333874] ICH4: IDE controller (0x8086:0x24cb rev 0x01) at PCI slot 0000:00:1f.1
[ 3.333889] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[ 3.333898] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[ 3.333913] ICH4: not 100% native mode: will probe irqs later
[ 3.333931] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:PIO
[ 3.333946] ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:PIO
[ 3.333956] Probing IDE interface ide0...
[ 3.347278] Floppy drive(s): fd0 is 1.44M
[ 3.362358] FDC 0 is a post-1991 82077
[ 3.620432] hda: WDC WD400BB-75DEA0, ATA DISK drive
[ 4.296118] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 4.296118] hda: UDMA/100 mode selected
[ 4.296118] Probing IDE interface ide1...
[ 5.031436] hdc: SAMSUNG CD-ROM SC-148C, ATAPI CD/DVD-ROM drive
[ 5.367059] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 5.367122] hdc: Disabling (U)DMA for SAMSUNG CD-ROM SC-148C (blacklisted)
[ 5.367130] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 5.367206] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 5.367246] ide1 at 0x170-0x177,0x376 on irq 15
[ 5.399065] hda: max request size: 128KiB
[ 5.554155] hda: Host Protected Area detected.
[ 5.554155] current capacity is 78125000 sectors (40000 MB)
[ 5.554155] native capacity is 78165360 sectors (40020 MB)
[ 5.556436] hda: Host Protected Area disabled.
[ 5.556436] hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63
[ 5.556436] hda: cache flushes not supported
[ 5.556436] hda: hda1 hda2 hda3 hda4
[ 5.583979] hdc: ATAPI 48X CD-ROM drive, 128kB Cache
[ 5.583990] Uniform CD-ROM driver Revision: 3.20
[ 6.181724] PM: Starting manual resume from disk
[ 6.234813] ReiserFS: hda1: found reiserfs format "3.6" with standard journal
[ 6.234833] ReiserFS: hda1: using ordered data mode
[ 6.241585] ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 6.242572] ReiserFS: hda1: checking transaction log (hda1)
[ 14.254621] ReiserFS: hda1: replayed 697 transactions in 7 seconds
[ 14.299128] ReiserFS: hda1: Using r5 hash to sort names
[ 17.215589] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 17.719491] Linux agpgart interface v0.103
[ 17.734836] agpgart: Detected an Intel 830M Chipset.
[ 17.734970] agpgart: Detected 892K stolen memory.
[ 17.753034] agpgart: AGP aperture is 128M @ 0xf0000000
[ 17.938265] input: Power Button (FF) as /class/input/input1
[ 17.966761] ACPI: Power Button (FF) [PWRF]
[ 17.966876] input: Power Button (CM) as /class/input/input2
[ 17.999078] ACPI: Power Button (CM) [VBTN]
[ 19.005080] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 19.047074] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 19.085013] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 19.085112] iTCO_wdt: failed to reset NO_REBOOT flag, reboot disabled by hardware
[ 19.085170] iTCO_wdt: No card detected
[ 19.231216] intel_rng: FWH not detected
[ 19.378980] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17
[ 19.406808] input: PC Speaker as /class/input/input3
[ 19.434275] Real Time Clock Driver v1.12ac
[ 20.004059] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
[ 20.004102] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 20.197280] input: ImPS/2 Generic Wheel Mouse as /class/input/input4
[ 20.229435] parport_pc 00:0a: reported by Plug and Play ACPI
[ 20.229495] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 20.422816] intel8x0_measure_ac97_clock: measured 54782 usecs
[ 20.422822] intel8x0: clocking to 48000
[ 22.635596] Adding 979956k swap on /dev/hda3. Priority:-1 extents:1 across:979956k
[ 29.232799] ReiserFS: hda1: Removing [4 50189 0x0 SD]..done
[ 29.232894] ReiserFS: hda1: There were 1 uncompleted unlinks/truncates. Completed
[ 29.944473] loop: module loaded
[ 30.050892] device-mapper: uevent: version 1.0.3
[ 30.053432] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 47.309071] ReiserFS: hda4: found reiserfs format "3.6" with standard journal
[ 47.309071] ReiserFS: hda4: using ordered data mode
[ 47.312541] ReiserFS: hda4: journal params: device hda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 47.313376] ReiserFS: hda4: checking transaction log (hda4)
[ 47.339641] ReiserFS: hda4: Using r5 hash to sort names
[ 47.383862] ReiserFS: hda2: found reiserfs format "3.6" with standard journal
[ 47.383862] ReiserFS: hda2: using ordered data mode
[ 47.391981] ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 47.392570] ReiserFS: hda2: checking transaction log (hda2)
[ 47.410735] ReiserFS: hda2: Using r5 hash to sort names
[ 47.410802] ReiserFS: hda2: Removing [2 23 0x0 SD]..done
[ 47.410802] ReiserFS: hda2: Removing [2 22 0x0 SD]..done
[ 47.410802] ReiserFS: hda2: Removing [2 17 0x0 SD]..done
[ 47.410802] ReiserFS: hda2: There were 3 uncompleted unlinks/truncates. Completed
[ 48.959887] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[ 52.894565] NET: Registered protocol family 10
[ 52.895405] lo: Disabled Privacy Extensions